Radio Frequency Based Wireless Batch Counting Device For Brewery

Project and Seminar Material for Computer Engineering

Radio Frequency Based Wireless Batch Counting Device For Brewery


Abstract


This project work deals on the design and implementation of a Rf based wireless batch counting device for brewery capable of counting the bottled products in the conveyor and displaying the value numerically and wirelessly to its receiver installed about 100 meters away. This project is realized in two functional units: the transmitter and receiver units. The transmitter unit is installed in the conveyor while the receiver unit is installed at a remote location. They interact by the principle of electrical resonance using Radio frequency transmission waveband.

An Opto-coupler realized with Light dependent Resistor (LDR) and Laser diode form the sensor/electronic eye that detects the presence of bottle. The output signal of the sensor unit is processed and used to cause the Tuned Radio Frequency (TRF) transmitter module to radiate an Rf signal to its receiver, some meters away. On receiving the radiated signal, its output is processed and used to clock a 2-digit decimal counting unit that displays the number of counted bottles numerically.

This system implies a lot in computer, and EEE. As a surveillance system, if the recorded value is not equal to the single unit version also installed in the front end of the conveyor, the workers involved will be fired. This system can only communicate to the receiver over a range of 100m maximum. At the end of every production cycle, if the recorded value on the stand alone type is less than the value recorded by this system, the workers get queried. The result being a system which can count the number of bottled drinks and relay the number/value wirelessly to a receiver some meters away. It is not microprogram control rather pure random logic.


Chapter One


Introduction

1.1. Background of the Study

Owing to the high rate of industrial espionage and theft, industrial security techniques need to be improved to arrest/combat pilfering in industries. This project work tries to bring in an improved security measure which can be used to check pilfering in Brewery industries. Pilfering of bottled drinks is a common theft in Breweries. And this act is perpetrated in the conveyor before a standalone counting device takes account of it. This has a tremendous effect on the stature of the fire – if it is not properly checked, could lead to liquidation and bankrupts of the firm.

Conventionally, there is a batch counting device that counts the bottled drinks and displays the values numerically at same spot carrier criminals who pilfer the products divert it before the counter. This chronology in social vices in the brewery industry has motivated me to embark on a project that is capable of counting/the bottled drinks in the capable of counting/the bottled drinks in the conveyor and display the value numerical and wirelessly (using Rf transmission waveband) to its receiver installed about 100m away. This device will count the product before it gets to the standalone version. This technique will help to check pilfering and bring industrial espionage to halt.


1.2. Problem Statement

Brewery industries all over world face the problem of pilfering of the products by the workers most frequently in the conveyer. This menace gave way to the development of a stand alone batch counting device which is usually installed in the conveyors to record the total number of bottled products. This techniques is facing serious threat since the bad-eggs pilfer/divert the products before it gets to the counter.

Owing to the challenges mentioned above, there is need to develop a system which will be installed at the entry point of the conveyors to count the products without the consent of the workers and display the value to a receivers unit installed in the manager office using Radio-frequency technology.


1.3. Aims and Objectives

The aim of this project is to design and implement a Radio frequency based wireless batch counter capable of counting bottled drinks/products and display it at a remote location.

  1. To develop system which can communicate using Radio frequency technology.
  2. To develop an opto coupler module which can detect opaque objects like bottle using laser diode and visible light
  3. To develop a 2-digit decimal counting unit which can count from 00-99.
  4. To develop a system which is pure hardwired. No micro-program.
  5. To develop a power supply unit that can power Rf device.

1.4. Significance of the Project

This project work signifies a lot in telecom, computer and electronic engineering it is very useful in a number of domestic places like in bedroom and security lamps in the compound. A project of this type if modified can be used as a gate/door opening system, car immobilizer and for industrial process control. Another vital significance of this system is in the control of Air conditioner and refrigerators and other lamps in modern buildings. This system can be used to start and stop a power generating set from a distance.


1.5. Scope of the Project

This project work covers the following; Tuned Radio-frequency transmitter and receiver modules, Ne555 timer, Decimal counting unit, Decoders and transistors and electromagnetic relay. It also lays great emphasis on passive and active components used to implement the system. It also x-rays the mode of calculations of the basic parameters used in the design and other areas of application of the device. This report elaborates on the block diagram and principle of operation of the system.


1.6. Limitations

  1. This project work is focused on the design and implementation of Rf batch counter for brewery.
  2. It is a prototype of the real-life system due to the ratings of the components used to implement it.
  3. It can only count products in an opaque bottle? (Filled or partially filled)
  4. It uses only Radio frequency to communicate with the receiver
  5. The system is powered using power from MAINS.
  6. The receiver displays a maximum of 100 counts (00-99) and does not contain a memory device for storage of data.

1.7. Project Report Organization

This project report is presented in six chapters to appropriately illustrate the steps involved in its implementation. Chapter one introduce the design overview, objectives and significance of the project. Chapter two is basically the literature review and some theories relevant to the design. Chapter three is on the system design analysis while chapter four elaborates on the implementation, testing and result. Finally chapter five summarizes the entire thesis and recommendations.


1.8. Definition of Terms:

Radio Frequency (RF):

This is the rate of oscillation within the range of in the electromagnetic wave spectrum.

Control Logic Generator:

This module also called the signal conditioning unit generates the logic which is needed to bias a transistor driver or to trigger/clock a resettable IC. It is realized with schmitt trigger NAND gate.

Inductive Kick-Back Diode:

This is diode that is connected across the terminals (coil) of an inductive load to prevent inductive kick-back when it is switched off/de-energized.

Resonance:

This is a phenomenon which occurs when a vibrating body set another body into vibration until both vibrate at the same natural frequency. It is the principle behind Rf communication.

Frequency Modulation:

This is a technique of signal transmission in which the frequency of the signal is varied while the amplitude and phase remain constant.

One Shot Delay:

This is multivibrator circuit configure monostable mode which gives out a one-shot pulse when it is triggered. It is used to delay proceeding operation.


Chapter Five


Conclusion and Recommendation

5.1 Conclusion

The project design and construction of a RF based wireless batch counter for brewery was a dream-come through since 98% of the goal was achieved. The remote is a portable handheld Rf type which is omni directional in transmission. Its transmission is not hampered by Radio broadcasting stations because it was carefully set to a free frequency. The range of the transmission was nearly 100m in open air but shorter indoors due to reflection of Rf by opaque objects. The fan speed was changing in response to the display. This device is of paramount need and should be adopted by everybody.


5.2 Recommendation

It is said that theory without practical is lame and practical without theory is blind. Taking the theoretical aspect of any engineering course is very necessary because it gives the basis for building the students to become better engineers. With the fast technological development in the world, students should be subjected to develop interest in design courses. In encouraging the upcoming student, showrooms should be made available where projects both present and past should be stored for future references. The provision of departmental libraries helps to facilitate researchers. This can be used to replace CCTV (Close Circuit Television for Security Surveillance) used as a security gadget in most Banks and Malls.


Radio Frequency Based Wireless Batch Counting Device For Brewery


Project Material Download

3,000 Naira


The complete material will be sent to you in just 2 steps.

Quick & Simple…


Step One Purchase

Make payment of ₦3,000: through USSD Transfer, Bank Mobile App, ATM Transfer, or POS Transfer to:

Access Bank PlcAccount No.: 0811003731
Name: Samphina Academy
Account Type: Current

Or Click Here to pay with Debit Card

FOR CLIENTS OUTSIDE NIGERIA:
Click Here to pay with Debit Card ($15)
GHANA – Make Payment of 60 GHS to MTN MoMo, 0553978005, Douglas Osabutey 

  PAY WITH CRYPTOCURRENCY


Step Two Purchase

Send the following details through Text Message or WhatsApp Messenger | +234-8143831497

  • Payment Details 
  • Email Address 
  • Radio Frequency Based Wireless Batch Counting Device For Brewery

The complete material will be sent to your email address after receiving your payment information | T & C Apply


  Contact Our Help Desk


You may also like:

⚠️ Need a different topic? Perform a quick search



Get A Complete Business Plan For Any Business In Nigeria

Business Plan for Businesses in Nigeria

  Business Plans in Nigeria


Radio Frequency Based Wireless Batch Counting Device For Brewery


Disclaimer

This research material “Radio Frequency Based Wireless Batch Counting Device For Brewery” is for research purposes and should be used as a guide in developing your research project / seminar work. For no reason should you copy word for word (verbatim) as samphina.com.ng will not be liable for any who copied the material.

The aim of providing this material is to reduce the stress of moving from one school library to another all in the name of searching for research materials. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works. According to Austin Kleon “All creative work builds on what came before”.

samphina.com.ng is only providing this material “Radio Frequency Based Wireless Batch Counting Device For Brewery” as a reference for your research. The paper should be used as a guide or framework for your own paper. The contents of this paper should be able to help you in generating new ideas and thoughts for your own research. Use it as a guidance purpose only.


How to defend your research work


This is a general guide on how to defend your research work:

1. Prepare For Questions:

If you are preparing for questions that may be asked during your defense, then your answers will flow smoothly and effectively. This will prove your knowledge on the subject e.g “Radio Frequency Based Wireless Batch Counting Device For Brewery“, and strengthening your argument. Ask friends and family, read your work for them to listen to your presentation, and write down questions. You may be lucky the panel will ask you those you have already prepared on.

2. Strong Summary:

Summarizing your chapters will help keep your audience focused because it is easy for a mind to drift, so providing summaries will ensure your panel will follow along, even if they lose focus for a brief moment. Visual aides, such as graphs and power-point presentations can be very helpful. If you are going to use these, make sure you will practice your presentation with them.

3. Be Confident in Your Research Work:

Not knowing your topic “Radio Frequency Based Wireless Batch Counting Device For Brewery” inside out will cause you to struggle and ultimately fail with your defense. You need to know the subject from every angle to ensure you are fully prepared for any question that may come your way.

4. Conclusion:

Reinforce your findings to conclude your defense. The finale of your presentation should focus on proving the work that has been done. You may need to recap on what has changed and remained unchanged, if is necessary.

5 . Listen:

Before you get defensive or recite a particular answer, make sure you truly understand the question being asked. Being a good listener is an important quality, because providing an inaccurate or off-topic answer will also weaken the validity of your paper.

Samphina Academy

Samphina Academy is an Online Educational Resource Center that is aimed at providing students with quality information and materials to aid them in succeeding in their academic pursuit.